A full range of aluminium profiles
and door materials.

Slim sightline profiles for sliding and telescopic door systems, available in anodised and powder-coated finishes. Designed to hold a glass panel square while keeping the visible frame section as narrow as possible.

Frame, track and cover profiles are supplied as a set and matched to the rollers and tracks we carry, so the system components are compatible from the start.

• Slim sightline sections for sliding and telescopic systems
• Frame, track and cover profiles that work as a set
• Trade quantities, with consistent finish across repeat orders

Genuine OPK roller sets for sliding door systems — single, double and heavy-duty configurations, plus the brackets and bottom guides that complete the installation. OPK rollers are specified for consistent performance on heavy glass panels.

Tell us the panel weight and the track you are working with and we will confirm which roller configuration is appropriate.

• Low-friction wheels for quiet travel on heavy panels
• Matched top and bottom guides for alignment
• Replacement sets available for existing installations

A telescopic sliding system allows two or three panels to stack into the space of one, so the clear opening spans nearly the full frame width. This makes it suitable for large interior and exterior openings where maximum clear width is needed.

We supply telescopic hardware for both manual and automatic operation, with profiles and rollers selected to match the panel weight and opening dimensions.

• Panels run in sequence and park in one stack
• Hardware for automatic drive or manual operation
• Works with fluted, clear and decorative glass

Synchronized door hardware links two panels so they travel as one unit, either opening from the centre or moving in the same direction. This increases the clear opening width without requiring a larger frame.

We supply hardware for automatic operation with motorized drives and sensor activation, and for manual synchronized systems where a powered setup is not required.

• Paired panels with coordinated travel
• Options for automatic and manual control
• Hardware for commercial entrances and interior partitions

A pocket door slides the panel into the wall cavity, leaving a completely clear opening without a swing arc or exposed door face. It is commonly specified where floor space is limited or where a flush wall finish is required on both sides.

We supply pocket frames, overhead tracks and runners sized to the opening, together with the alignment fittings that keep the panel travelling correctly as it enters the cavity.

• Frame and track supplied together, sized to the opening
• Smooth travel for heavy timber and glass panels
• Flush finish on both faces of the wall

A flush door sits level with the surrounding wall with no visible frame or architrave. Because the door surface and wall finish are continuous, the concealed hardware needs to be accurately fitted — there is no frame detail to cover minor misalignment.

We supply the concealed frames, hinges and handles that make the detail work.

• Frames that finish flush with plaster or panelling
• Hardware selected for the door weight and swing
• Handles in the same finish family as the range

A pivot door turns on an axis set into the floor and head, rather than hanging from a side frame. It allows a much wider, taller panel — and a dramatic, nearly frameless opening.

We supply the floor and ceiling pivot sets, rated for the panel, plus the seals and stops that keep it turning cleanly.

• Pivot sets for tall and heavy glass or timber panels
• Adjustable for alignment after installation
• Paired with slim perimeter profiles for a flush finish

A corner system carries the panel around a 90° turn, so two adjacent walls can open as one continuous corner. It is the detail that makes a balcony or terrace feel like an extension of the room.

We supply the curved track sections and the roller sets that handle the transition without the panel jumping.

• Corner track sections matched to the straight runs
• Rollers that hold alignment through the turn
• Used for terraces, balconies and open-plan corners

Folding panels concertina to one side, stacking into a fraction of the opening. Where a telescopic system needs depth behind the wall, a folding system needs almost none — useful where the return wall is short.

We supply the top tracks, hinges, carriers and guides that keep a multi-panel run folding in sequence.

• Panels fold and stack without needing wall depth
• Carriers and hinges matched to panel count
• Options for interior partitions and exterior openings

The bathroom side of the range: hinges, clamps, handles, stabiliser bars and seals for glass shower enclosures — supplied as a set so the finish matches across every panel.

We stock the black, chrome and brushed finishes that current bathrooms are specifying.

• Frameless and semi-frameless enclosure fittings
• Matte black, chrome and brushed metal finishes
• Complete sets rather than loose components

The part the client actually touches. We supply slim pull handles, lever sets, locks and patch fittings in finishes that match the profiles — so the door reads as one object rather than a frame with something bolted on.

Available to match the black, champagne, silver and anodised profile finishes in the range.

• Handles sized for glass, timber and flush doors
• Finishes matched to the profile range
• Fittings and fixings supplied together